|
|
SPEED UP CUSTOM SHEET METAL FABRICATION
12" Planishing Hammer w/ 9 Radius Anvils Includes & Features:
Rear adjuster sets load force and allows for fast die changes.
Rugged tubular construction.
9 Lower Radius Anvils Included Standard:
Flat, 3/4", 1-1/2", 2", 3", 4", 6", 8", and 12"
Foot pedal operation allows both hands free to be on your work!
PRO TIPS:
> Be sure to use low air pressure for 'smoothing' your metal work, and use slightly higher air pressure when 'shaping' your project.
> To avoid leaving marks on your metal, always select a die that closely matches the shape you are forming or smoothing for best results.
MADE IN THE USA
|
950.00 |
|
|
SPEED UP CUSTOM SHEET METAL FABRICATION
24" Planishing Hammer w/ 9 Radius Anvils Includes & Features:
Rear adjuster sets load force and allows for fast die changes.
Rugged tubular construction.
9 Lower Radius Anvils Included Standard: Flat, 3/4", 1-1/2", 2", 3", 4", 6", 8", and 12".
Foot pedal operation allows both hands free to be on your work!
PRO TIPS:
> Be sure to use low air pressure for 'smoothing' your metal work, and use slightly higher air pressure when 'shaping' your project.
> To avoid leaving marks on your metal, always select a die that closely matches the shape you are forming or smoothing for best results.
MADE IN THE USA
|
1100.00 |
|
|
MOTORCYCLE METAL FABRICATION: from Sheet to Street
Watch master metal fabricator Ron Fournier create custom motorcycle sheet metal parts from scratch, including construction of an aluminum tank, fairing and front fender in this comprehensive film.
Also featured is step-by-step fabrication of the bike's entire rear section which includes the fender, sides and seat pan. Each step and every technique is clearly demonstrated in a manner that shows the viewer how to make custom parts of their own design.
The entire metal shaping process is detailed with thorough explanations & helpful tips to 'de-mystify' metal working magic. From pattern to finished product - Ron explains custom metal work - the result is professional and ready for paint. Armed with fundamental metal shaping knowledge, some essential tools - and a few "tricks of the trade", you can take your next project from sheet to street!
Demonstration & Instruction on:
Project Planning
Pattern Development
Buck Design & Fabrication
Annealing
Blocking and Smoothing
Metal Shaping using an English wheel
Shrinking & Stretching
Heliarc Tack-Welding & Gas Welding
Tips on Final Trim & Fit
Metal Finishing
Over 3-1/2 hours of metal working instruction in this 2 DVD SET!
|
60.00 |
|
|
Simple and quick to use!
Just drill a pilot hold for the draw bolt, then apply the tool and tighten the bolt for a smooth, flared hole in one easy step;
Punch hole only by removing female flare ring and use punch and die;
Easily mounts into Mittler Brothers bench presses;
Features
Automotive (standard) punch and flare tools are designed to punch the required hole size and follow with a 45-degree radius angle (leg length of ¼") in metal thickness of .040” to .065” aluminum and mild steel.
The total clearance after the punch/flare is made will be 1/8” larger than the punch size. (e.g. 1” OD punch will enlarge to 1-1/8” OD after punch/flare.)
Punch to die clearance is 0.012”
Anti friction bearings are included.
ONE SIZE: 1" punch and flare tool
MADE IN THE USA
View: Optional punch/flare setup using a bench press
|
120.00 |
|
|
Simple and quick to use!
Just drill a pilot hold for the draw bolt, then apply the tool and tighten the bolt for a smooth, flared hole in one easy step;
Punch hole only by removing female flare ring and use punch and die;
Easily mounts into Mittler Brothers bench presses;
Features
Automotive (standard ) punch and flare tools are designed to punch the required hole size and follow with a 45-degree radius angle (leg length of ¼”) in metal thickness of .040” to .065” aluminum and mile steel.
The total clearance after the punch / flare is made will be 1/8” larger than the punch size. (e.g. 1” OD punch will enlarge to 1-1/8” OD after punch/flare.
Punch to die clearance is 0.012”
Anti friction bearings are included.
ONE SIZE: 1-1/2" punch and flare tool
MADE IN THE USA
View: Optional punch/flare setup using a bench press
|
135.00 |
|
|
Simple and quick to use!
Just drill a pilot hold for the draw bolt, then apply the tool and tighten the bolt for a smooth, flared hole in one easy step;
Punch hole only by removing female flare ring and use punch and die;
Easily mounts into Mittler Brothers bench presses;
Features
Automotive (standard ) punch and flare tools are designed to punch the required hole size and follow with a 45-degree radius angle (leg length of ¼”) in metal thickness of .040” to .065” aluminum and mile steel.
The total clearance after the punch / flare is made will be 1/8” larger than the punch size. (e.g. 1” OD punch will enlarge to 1-1/8” OD after punch/flare.)
Punch to die clearance is 0.012”
ONE SIZE: 1-1/4" punch and flare tool
MADE IN THE USA
View: Optional punch/flare setup using a bench press
|
120.00 |
|
|
Simple and quick to use!
Just drill a pilot hold for the draw bolt, then apply the tool and tighten the bolt for a smooth, flared hole in one easy step;
Punch hole only by removing female flare ring and use punch and die;
Easily mounts into Mittler Brothers bench presses;
Features
Automotive (standard ) punch and flare tools are designed to punch the required hole size and follow with a 45-degree radius angle (leg length of ¼”) in metal thickness of .040” to .065” aluminum and mile steel.
The total clearance after the punch / flare is made will be 1/8” larger than the punch size. (e.g. 1” OD punch will enlarge to 1-1/8” OD after punch/flare.
Punch to die clearance is 0.012”
Anti friction bearings are included.
ONE SIZE: 1-3/4" punch and flare tool
MADE IN THE USA
View: Optional punch/flare setup using a bench press
|
135.00 |
|
|
Simple and quick to use!
Just drill a pilot hold for the draw bolt, then apply the tool and tighten the bolt for a smooth, flared hole in one easy step;
Punch hole only by removing female flare ring and use punch and die;
Easily mounts into Mittler Brothers bench presses;
Features
Automotive (standard ) punch and flare tools are designed to punch the required hole size and follow with a 45-degree radius angle (leg length of ¼”) in metal thickness of .040” to .065” aluminum and mile steel.
The total clearance after the punch / flare is made will be 1/8” larger than the punch size. (e.g. 1” OD punch will enlarge to 1-1/8” OD after punch/flare.
Punch to die clearance is 0.012”
Anti friction bearings are included.
ONE SIZE: 2" punch and flare tool
MADE IN THE USA
View: Optional punch/flare setup using a bench press
|
145.00 |
|
|
Simple and quick to use!
Just drill a pilot hold for the draw bolt, then apply the tool and tighten the bolt for a smooth, flared hole in one easy step;
Punch hole only by removing female flare ring and use punch and die;
Easily mounts into Mittler Brothers bench presses;
Features
Automotive (standard ) punch and flare tools are designed to punch the required hole size and follow with a 45-degree radius angle (leg length of ¼”) in metal thickness of .040” to .065” aluminum and mile steel.
The total clearance after the punch / flare is made will be 1/8” larger than the punch size. (e.g. 1” OD punch will enlarge to 1-1/8” OD after punch/flare.
Punch to die clearance is 0.012”
Anti friction bearings are included.
ONE SIZE: 2-1/2" punch and flare tool
MADE IN THE USA
View: Optional punch/flare setup using a bench press
|
135.00 |
|
|
Simple and quick to use!
Just drill a pilot hold for the draw bolt, then apply the tool and tighten the bolt for a smooth, flared hole in one easy step;
Punch hole only by removing female flare ring and use punch and die;
Easily mounts into Mittler Brothers bench presses;
Features
Automotive (standard ) punch and flare tools are designed to punch the required hole size and follow with a 45-degree radius angle (leg length of ¼”) in metal thickness of .040” to .065” aluminum and mile steel.
The total clearance after the punch / flare is made will be 1/8” larger than the punch size. (e.g. 1” OD punch will enlarge to 1-1/8” OD after punch/flare.
Punch to die clearance is 0.012”
Anti friction bearings are included.
ONE SIZE: 3" punch and flare tool
MADE IN THE USA
View: Optional punch/flare setup using a bench press
|
160.00 |
|
| |
|