|
|
Simple and quick to use!
Just drill a pilot hold for the draw bolt, then apply the tool and tighten the bolt for a smooth, flared hole in one easy step;
Punch hole only by removing female flare ring and use punch and die;
Easily mounts into Mittler Brothers bench presses;
Features
Automotive (standard ) punch and flare tools are designed to punch the required hole size and follow with a 45-degree radius angle (leg length of ¼”) in metal thickness of .040” to .065” aluminum and mile steel.
The total clearance after the punch / flare is made will be 1/8” larger than the punch size. (e.g. 1” OD punch will enlarge to 1-1/8” OD after punch/flare.
Punch to die clearance is 0.012”
Anti friction bearings are included.
ONE SIZE: 2-1/2" punch and flare tool
MADE IN THE USA
View: Optional punch/flare setup using a bench press
|
135.00 |
|
|
Simple and quick to use!
Just drill a pilot hold for the draw bolt, then apply the tool and tighten the bolt for a smooth, flared hole in one easy step;
Punch hole only by removing female flare ring and use punch and die;
Easily mounts into Mittler Brothers bench presses;
Features
Automotive (standard ) punch and flare tools are designed to punch the required hole size and follow with a 45-degree radius angle (leg length of ¼”) in metal thickness of .040” to .065” aluminum and mile steel.
The total clearance after the punch / flare is made will be 1/8” larger than the punch size. (e.g. 1” OD punch will enlarge to 1-1/8” OD after punch/flare.
Punch to die clearance is 0.012”
Anti friction bearings are included.
ONE SIZE: 3" punch and flare tool
MADE IN THE USA
View: Optional punch/flare setup using a bench press
|
160.00 |
|
|
SET OF 6 LOWER ANVILS #: 2900-A-Series
CNC Machined. Quality manufactured of heat treated steel. Anvils are hard turned after heat treat for concentricity. 2-1/2" Dia x 2" Wide.
Check out the wheel (above) one of our workshop students built using these anvils!
INCLUDES:
2900-A0, FLAT anvil wheel
2900-A1, 12" Rad with 3/4" flat anvil wheel
2900-A2, 8-1/2" Rad with 1/2" flat anvil wheel
2900-A3, 5" Rad with 3/8" flat anvil wheel
2900-A4, 3-1/4" Rad with 1/4" flat anvil wheel
2900-A5, 2-3/8" Rad with 1/8" Flat anvil wheel
SAVE WHEN YOU BUY THE SET OF SIX! (Normally $95 ea.)
Made in USA
|
555.00 |
|
|
Ron brings his signature easy-to-follow style using the English wheel, a machine notoriously difficult for beginners to figure out.
Demonstrations are given on a broad range of machines from a cast iron 'monster' to a tiny C-clamp.
This comprehensive film includes the machine's history as well as a clear explanation of principles that enable the machine to move metal. Ron shows basic tracking patterns that are used to shape panels of various sizes and configurations.
In addition to common wheeling techniques, Ron also shows some less well-know processes, such as using a rubber top wheel and embossing with the machine.
Whether you are brand new to the English wheel or an experienced user you will find lots valuable information!
|
40.00 |
|
|
What do you do if you have a car with a fender that is damaged beyond repair, or missing? Ron shows how to use the opposite fender to design a buck, pointing out the features required to make a new fender that perfectly mirrors the model. You will see him analyze a '36 Ford fender, determine the number of pieces to make it from, and exactly where to place the seams to accommodate the intricate details, including the running board bulge and the rolled edge of the wheel opening.
A fascinating, in-depth look at the start-to-finish construction of a challenging project!
119 min., #1000-24
|
40.00 |
|
|
Ron Covell demonstrates dozens of ways to work with tubing, including bending with heat, bending with tube bending machines (both inexpensive and high-end machines), mitering, flaring and tapering tubing.
An extensive section deals with using U-bends, showing how to create anything from simple water pipes to elaborate headers.
One of Ron's most popular videos ~ great information communicated concisely with lots of close up shots!
DVD, 95 min., #WTV01 (1000-4)
|
40.00 |
|
|
Featuring Ron Fournier & Ron Covell
Two of the best-known names in metalshaping have teamed up to teach you the ins and outs of the hammerforming process. The two Ron's bring over 70 years of combined experience to their viewers, and you will see how their individual styles of working with metal compliment each other.
Hammerforms are very easy to make, and they enable you to create parts that have the look and accuracy of die-stamped parts. Even beginning metalworkers can use hammerforms to quickly and easily make parts of which they can be proud.
Ten different hammerforming operations are demonstrated, from simple tank tops to a beautiful rolled edge detail on a complicated pontoon Bugatti fender.
The film includes instruction and demonstrations on the following topics:
Tank Top
Grille Bar
Annealing
Chipmunk Tombstone
Bowl Shapes
Flying Wire Fairing
Wing Rib
Door Post
Naca Duct
Bicycle Seat Post
Bugatti Fender
Featuring striking close-up shots that bring you close to the action, and clear descriptions of every aspect of the hammerforming process.
Length, 76 min. #HFD00 (1000-15)
|
10.00 |
|
|
MIG Welding is widely used, but few people really understand how each of the variables affects the finished weld. This program can be easily understood by a beginner, but it covers information even seasoned professionals can learn from. Ron Covell goes through the entire process step-by-step, and gives clear descriptions of how each factor affects the weld, including wire speed, voltage, stickout, gun angle, travel speed, and gas flow. He also covers plug welds, patch panels, welding aluminum, and using flux core wire.
You’ll especially enjoy the special bonus section on Plasma Cutting!
70 minute DVD, # 1000-22
|
40.00 |
|
|
34" High
Accomodates up to a 19" Diameter Shot Bag (sold separately)
Heavy Duty, Perfect for the Professional Heavy Welded Steel Top Plate
Hammer Storage
Weight 57 lbs.
Please note:
Tools are NOT included with stand and are shown for illustration purposes.
This item only ships within the Contiguous US. Please do not add to your cart if you are outside of this region. Thank you for your understanding.
|
230.00 |
|
|
This program covers many advanced topics in TIG welding, including welding chrome moly steel, stainless steel, aluminum, magnesium, bronze, copper, and titanium. You’ll also learn how to weld castings made from aluminum, magnesium, and bronze. Clear guidelines are given for using the pulse and waveform adjustments that many new welders have, along with great practical advice on machine setup, joint preparation, and weld finishing.
Ron’s clear and detailed instructions are easy to follow, and the striking close-up photography shows you exactly what to look for as you weld!
111 min., #1000-25
|
40.00 |
|
| |
|