|
|
A necessity for Metal Workers! Ron's popular follow-up reference book to Metal Fabricator's Handbook.
INSIDE YOU WILL FIND TIPS ON: Setting up your own shop, proper use of the English wheel, basic metal shaping techniques, the art of hammerforming, proper riveting techniques, and tips on restoring original sheet metal.
Fully illustrated how-to sequences are included, along with many photos to develop sheet metal skills.
|
28.00 |
|
|
Sections include: Tool selection and use, MIG, TIG, arc- and gas-welding, Fuel and oil tanks, Exhaust headers, Roll bars and roll cages, Sheet metal interiors and Basic metal shaping.
This practical book shows how to build structurally sound, good looking metal parts for custom street rods, race cars or restorations. Over 350 step-by-step photos and instructions illustrate proper welding, metal shaping and design techniques.
"For the reader with more than a passing interest in automotive fabrication, this book is an excellent acquisition." -Road & Track
MOTO Award Winner for Best Technical How-to Book in 1984
|
25.00 |
|
|
Metalworking Tools & Kits
Fournier signature metalworking tools and metalworking tool kits are popular with metal fabricators world-wide!
|
|
|
Metal Finishing
Weld finishing and final planishing are achieved with some of the metal working "tools of the trade"
|
|
|
MIG Welding is widely used, but few people really understand how each of the variables affects the finished weld. This program can be easily understood by a beginner, but it covers information even seasoned professionals can learn from. Ron Covell goes through the entire process step-by-step, and gives clear descriptions of how each factor affects the weld, including wire speed, voltage, stickout, gun angle, travel speed, and gas flow. He also covers plug welds, patch panels, welding aluminum, and using flux core wire.
You’ll especially enjoy the special bonus section on Plasma Cutting!
70 minute DVD, # 1000-22
|
40.00 |
|
|
How To Gas-Weld Aluminum by Ron Fournier covers essential equipment, methods and benefits of tack-welding, fitting and joint preparation, and how to produce fusion-type welds with lipping, butt-welds and tank corner welds. Demonstrations of straight welds, corners and curved sections are included in this instructional film.
Note: This DVD is also included in our DHC2000 (Cobra) Welding Torch Kit!
|
30.00 |
|
|
Metal work tools hand-picked for every day usefulness in custom metal fabrication shops!
|
|
|
Just drill a pilot hole for the draw bolt and then apply the tool and tighten. The finished hole is smooth and has a stengthening bead.
Use in Mittler Bench Presses with spring loaded center pin and just center punch, no drilling needed.
These can also be used as regular hole punches by not using the flare forming ring.
Anti-friction bearings are included with purchase.
AUTOMOTIVE PUNCH & BEAD TOOL KIT OF 6 SIZES INCLUDES:
1"
1-1/4"
1-1/2"
1-3/4"
2"
2-1/2"
MADE IN THE USA
|
720.00 |
|
|
Just drill a pilot hole for the draw bolt and then apply the tool and tighten. The finished hole is smooth and has a stengthening bead.
Use in Mittler Bench Presses with spring loaded center pin and just center punch, no drilling needed. These can also be used as regular hole punches by not using the flare forming ring. Anti-friction bearings are included with purchase.
PUNCH & BEAD TOOL KIT OF 7 SIZES INCLUDES:
1"
1-1/4"
1-1/2"
1-3/4""
2"
2-1/2"
3"
MADE IN THE USA
|
860.00 |
|
|
Ron Covell demonstrates dozens of ways to work with tubing, including bending with heat, bending with tube bending machines (both inexpensive and high-end machines), mitering, flaring and tapering tubing.
An extensive section deals with using U-bends, showing how to create anything from simple water pipes to elaborate headers.
One of Ron's most popular videos ~ great information communicated concisely with lots of close up shots!
DVD, 95 min., #WTV01 (1000-4)
|
40.00 |
|
| |
|